FAQ - Frequently Asked Questions
|
Answer (See below for more questions.)
|
Assembly & Care
|
My head tube is somewhat out of round. What kind of problem is it?
|
It depends on how much the head tube is out of round. Seriously out of round head tubes can be a big problem and may require a factory repair. They are often caused by damage from an unusual impact.
The welding process will to some extent, ovalize the head tube. After welding, we machine and ream the head tube to assure a proper press fit with standard headsets. Some residual distortion may remain after welding, but it does not prevent proper headset installation. Steel has plenty of ability to move as you insert the head cups. Up to 1/2 (.5) mm discrepancy between the long and the short axis won't be a problem even for aluminum cups. Up to 1mm for steel cups will also work.
We can often "round" many damaged head tubes with special tools and techniques at the factory. In extreme cases, a new head tube may be required.
Many mechanics are not used to working with steel. Aluminum and carbon fiber are not nearly as forgiving as steel. Unless those materials are perfectly machined, you risk damaging the frame. Not so with steel, so you can install that headset with confidence.
|
Question List
|
Choosing Your Waterford
|
Do you want a racing bike, recreational bike or both?
|
What kind of maintenance does my Waterford need?
|
How big a tire do you want to fit on your bike?
|
How do you go about choosing your Waterford?
|
What if my seatpost slips during rides?
|
How versatile do you want your bike?
|
What kind of handling do you want?
|
What do I need to do to prevent rust and corrosion?
|
Why do we measure our seat tubes 'center to top'?
|
What do you want to carry?
|
How big a load do you want to carry?
|
If I'm a 180 pound rider, why does it matter whether my load is 15 pounds or 25 pounds?
|
Geometry and Fit
|
How does Waterford perform factory fittings?
|
What is toe-clip overlap and why do we avoid it?
|
My Fit Kit recommends a 538mm top tube. Nobody offers stock geometries in these sizes. What's my best fit?
|
Can't you just build a bike based on Fit Kit® measurements?
|
Why are your seat angles so steep on small frame sizes?
|
Why is there toe clip overlap on track geometries?
|
Why does Waterford recommend 650C or 26" wheels on selected sizes?
|
Why does Waterford sometimes recommend 650C or 26" wheels?
|
What if I want to change from a steel fork to a carbon fork or vica versa?
|
Materials & Construction
|
Retrofitting S&S Couplers?
|
What makes Waterford's Tubesets so Special?
|
Why Steel?
|
How much do color choices affect durability?
|
Lugs vs. TIG - Which is best?
|
Paints and Finish
|
How do I apply touch-up paint?
|
Why don't we Chrome Plate all Waterfords?
|
How do color choices affect durability?
|
Why not internal cable routing?
|
Wouldn't clearcoat over bare metal work?
|
Why not clearcoat only?
|
What's wrong with a matte finish?
|
Why can't I just give you a paint code to select custom paint?
|
Choosing a Finish
|
Upgrading Your Waterford
|
What kind of composite fork can I install on my Waterford?
|
General Information
|
Where do I find my serial number?
|
What does my serial number mean?
|
What is the difference between Gunnar and Waterford
|
What is the difference between 14-, 22- and 33-Series models?
|
Assembly & Care
|
What common dimensions are there for Waterfords - threading, bolts etc.?
|
My head tube is somewhat out of round. What kind of problem is it?
|
Which clamp diameter should I use to for my front derailleur
|
Clamp-on or braze-on front derailleurs.
|
What kind of care do I have to give my Waterford to prevent rust from forming?
|
How do I prevent my composite (carbon fiber) seatpost from slipping?
|
How long a seatpost do I need?
|
How do I get a good fit when installing downtube shift adapters?
|
How do I apply touch-up paint?
|
How do I apply replacement decals?
|
How do I remove my chainstay protector?
|
Should I use my Waterford on my Windtrainer?
|
Why did we go from 27.4mm to 27.2mm seatposts?
|
Why don't we install dropout adjusters on bikes that have adjuster holes?
|
I have an older model 1400 or 2400 off-road frame. What kind of front deraileur do I need?
|
What if I want to install a 1" for on a 1 1/8" head tube frame?
|
Threading: What is it for eyelets, rack mounts and so on?
|
Repair & Restoration
|
Why can't I just have Waterford touch up my frame instead of completely repainting it?
|
Is it worth it to restore my old Paramount, Raleigh or other classic road bike?
|
Can Waterford spread my dropouts on my old bike?
|
What does it take to retrofit my bike with S&S Couplers?
|
Will Waterford put its decals on a Paramount restoration?
|
Can I change the geometry on my existing frame?
|
I have a dent in my top tube, should I be concerned?
|
I have a chrome Paramount with damage to the chrome. Can you re-chrome it for me?
|
Buying / Selling a Waterford
|
How can I sell my Waterford?
|
Forks
|
Can I order a 1 inch steerer disc brake fork?
|
How can I get a disc brake fork with the ride of my classic steel rim brake fork
|
Warranty
|
Does Waterford provide Warranty Coverage?
|
Troubleshooting
|
What do I do for a stuck seatpost or bottom bracket?
|
What do I do for a slipping seatpost?
|
What should I do to prevent high-speed wobble and shimmy on my bike?
|
What do I do about brake chatter or shudder?
|
How do I reduce brake squealing?
|
How do I prevent my rear wheel from pulling under heavy climbing or sprinting?
|
What if I experience chain suck on my Off-Road frame.
|
Log in and Using this Web Site
|
Does my Waterford Login connect me to the Forum?
|
Paramount
|
What's the fork threading on the 1960's Paramounts
|
What do the markings mean found on the bottom bracket of Paramounts from the 50's to the 70's?
|
